LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 1
OWNER'S MANUAL
LS7600CD / LS7600CDW
AM/FM Stereo Receiver and Compact Disc Player
Designed for In-Wall Installation of All Recreational Vehicles, Motor Homes and Mobile Housings
12 Volts DC
®
A Registered Trademark of Magnadyne Corporation
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 3
CONTROLS AND FUNCTIONS
1. Power Button
9. Skip Up Button
Press this button in to turn the unit on. Press again to turn the
unit off.
To skip to the next higher track on the compact disc, press this
button.
2. AM/FM/CD Function Knob
After turning the unit on, select the desired playing mode with
this knob.
10. Program Button
Use the program button to arrange the tracks on the disc to
play in the order you wish. (See compact disc operation)
3. FM Stereo Indicator Light
11. Dial Indicator
When the tuner is receiving a strong stereo FM signal, the
stereo light will be lit.
The dial indicator will move up and down the scale as you
rotate the tuning knob (4) indicating the station you are lis-
tening to.
4. Radio Station Tuning Knob
12. 3-Band Graphic Equalizer
Rotate this knob to locate the radio station that you desire.
Rotating it clockwise will take you up the frequency band and
rotating it counter-clockwise will take you down the frequency
band.
These controls will tailor the overall tone of the unit. Slide
these controls up and down to achieve a tone that will suit
your taste.
5. Compact Disc Door
13. Volume Control Knob
By pressing the compact disc door above the word “PUSH” the
door will open to allow you to insert a compact disc.
Rotate this knob to increase the volume of the unit.
14. Speaker A/B Selector Buttons
6. Play/Pause Button
To play the "A" set of speakers, press the "Speaker A" button.
To play the "B" set of speakers, press the "Speaker B" but-
ton. To play the "A" and "B" speakers at the same time, press
both buttons in.
After inserting a compact disc press this button to begin com-
pact disc play. Pressing this button again will stop the compact
disc until the button is pressed again.
7. Stop Button
15. Headphone Output
When this button is pressed, compact disc play will stop.
The headphone jack accepts a standard walkman type head-
phone plug (3.5mm). When the headphones are plugged into
the headphone jack, all external speakers are turned off.
8. Skip Down Button
To skip to the next lower track on the compact disc, press this
button.
3
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 4
CONTROLS AND FUNCTIONS
16. Random Button
Compact Disc Operation
Use the random button to play the disc tracks in an random
order selected by the disc player computer.
1. Press the on/off button (1) in to turn the unit on.
2. Use the function knob (2) to select CD operation.
3. Press the door (5) and gently pull the compact disc door open
fully.
17. Repeat Button
Use the repeat button to continuously play one song repeatedly
or to continuously play the entire disc repeatedly.
4 Insert a disc onto the disc hub and press gently in the
center until the disc is secure and supported by the hub.
5. Close the compact disc door until it snaps into place.
6. Press the skip up/down buttons (8 / 9) to select a specific track.
7. Press the play button (6) and adjust the volume and 3 band
graphic equalizer controls as desired.
18. Compact Display
This display contains all the information about the disc that
is playing and all the modes the disc can play under.
(See compact disc operation)
Radio Operation
1. Press the on/off button (1) in to turn the unit on.
2. Use the function knob (2) to select the AM or FM radio band.
3. Tune in the desired radio station by rotating the tuning knob (4).
4. Adjust the volume and 3-band graphic equalizer controls as
desired.
Warning ! Never touch the laser eye. Moisture and oils
from your fingers can impair proper operation.
FM Stereo Operation
The unit will automatically switch from FM mono to FM stereo
when the signal strength increases to a stereo level. If the signal
should become weak on stereo reception, the unit will switch
back to the mono mode.
Note: Stereo operation is indicated by the stereo light (3) on the
front of the unit.
4
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 5
CONTROLS AND FUNCTIONS
Using the Program Feature:
Using the Random Feature:
If you desire to have the song selection of the disc played in a
different order than arranged on the disc, repeat the following
procedures to program the playing order.
The random feature allows the disc player to select the disc
tracks in an uncontrolled random play order. To initiate the ran-
dom play feature, press the random button (16) before pressing
the play button (6). When the play button is pressed, a moving
random indicator will appear in the display area while the com-
puter is searching for a track selection. When a song has finished
playing, the moving random indicator will appear in the display
again until the selection is made.
1. Press the program button (10). PGM
00 will appear in the display.
2.Use the skip up/down buttons (8/9) to
select the first song to play. Press the
program button to lock the selection.
Moving Random Indicator
3.Repeat step #2 as many times as
needed to determine the playing
order. You can program up to 21
selections.
TRACK
☛
TRACK
4.After programming is completed,
press the play button (6) to initiate the
program.
Note 1: After the program sequence has completed, pressing the
play button will start the play program again.
Note 2: Pressing the stop button (7) will stop the program. To re-
start the program, press the program button (10) and then press
the play button (6).
Note 3: Opening the compact disc door by pressing the CD door
(5) will clear the play selection programming.
5
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 6
CONTROLS AND FUNCTIONS
Using the Repeat Feature:
Handling the Disc:
The repeat feature has two modes of operation. A single track can
be continuously repeated or the entire disc can be continuously
repeated.
1. When inserting the disc, hold the disc with your thumb, middle
finger and index finger and press the center with your index
finger.
2. When removing the disc, always pull at the left or right edge
of the disc until it snaps loose from the disc hub. There are
indentations in the plastic for your fingers at these points.
TRACK
1. Press the repeat button one time while a track is playing.
REP1 will show in the display area. The track that is playing
will continuously repeat.
2x
TRACK
2. Press the repeat button two times while a track is playing.
REP will be displayed. When the last track on the disc has
finished playing, play will start over at track #1.
3. Always keep your disc’s clean and free from cracks,
fingerprints and dirt.
3x
TRACK
3. To turn off the repeat feature, press the repeat button (17) a
third time (the REP indicator will be off in the display).
6
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 7
INSTALLATION
Wall Panel
End Caps
Structural
Stud
Caution: Do not install radio without rear
cover installed. No user-serviceable parts
inside. Rear cover provides protection
against potential fire hazard.
7
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 8
POWER CONNECTIONS
This unit for use only with a 12 volt DC power
source with a negative ground.
RED Wire (+)
To 12 Volt DC Power
BLACK Wire (-) Ground
8
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 9
SPEAKER CONNECTIONS
Left Speaker (A)
Right Speaker (A)
+
+
_
_
BROWN Wire
GRAY Wire
WHITE Wire
ORANGE Wire
_
_
GREEN Wire
BLUE Wire
+
+
Speaker Connections: Do not confuse the A and B speaker sets
Left Speaker (B)
Right Speaker (B)
9
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 10
ANTENNA CONNECTIONS
External Automotive
Type Antenna Socket
Either
or
External Automotive
Type Antenna (Not Provided)
DP36AXT In-Wall Antenna (Not Provided)
If an automotive antenna is not available or is undesired, we
recommend the use of a Magnadyne DP36AXT di-pole anten-
na substitute. Plug the male plug from the DP36AXT into the
female receptacle of the LS7600CD/LS7600CDW unit and
allow the cable of the antenna to lay inside the wall.
The LS7600CD/LS7600CDW have a provision for a standard
automotive antenna. If an automotive antenna is used, plug
the male plug from the antenna into the female receptacle pro-
vided on the unit.
10
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 11
SAFETY INSTRUCTIONS
Read Instructions: All the safety and operating instructions
should be read before the appliance is operated.
Outdoor Antenna Grounding: If an outside antenna is con-
nected to the receiver, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built
up static charges. Section 810 of the National Electrical Code,
ANSI/NFPS no. 70-1983, provides information with respect to
proper grounding of the mast and supporting structure, ground-
ing of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, con-
nection to grounding electrodes, and requirements for the
grounding electrode. See figure 1.
Retain Instructions: The safety and operating instructions
should be retained for future reference.
Heed Warnings: All warnings on the appliance and in the oper-
ating instructions should be adhered to.
Follow Instructions: All operating and use instructions should
be followed.
Water and Moisture: The appliance should not be used near
water-- for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, etc.
Object and Liquid Entry: Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
Wall or Ceiling Mounting: The appliance should be mounted to
a wall or ceiling only recommended by the manufacturer.
Example of Antenna Grounding as per
National Electrical Code. Instructions
Contained in Artical 810-"Radio and
Television Equipment"
Heat: The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
Antenna Lead-In Wire (B)
Mast
Antenna Discharge
Unit (C)
Power Supply: The appliance should be connected to a power
supply only of the type described in the operating instructions or
as marked on the appliance.
Ground
Clamp
To Receiver
Ground
Wire
Cleaning: The appliance should be cleaned only as recom-
mended by the manufacturer.
(A,B)
Grounding
Clamps
Power Lines: An outdoor antenna should be located away from
power lines.
Figure 1.
Grounding Electrode
Drivin 8' Into the Earth
2.44 Meters
A) Use No. 10 AWG (5.3mm2) copper, No 8 AWG (8.4mm2) aluminum, No. 17
AWG (1.0mm2) copper clad steel or bronze wire, or larger, as ground wire.
B) Secure antenna lead-in and ground wires to house with stand-off insulators
spaced from 4 feet (1.22m) to 6 feet (1.83m) apart.
C) Mount antenna discharge unit as close as possible to where lead-in enters
house.
11
LS7600CDCDSGINS (SAMSUNG) 08/03/00 3:07 PM Page 12
WARRANTY
ONE (1) YEAR LIMITED WARRANTY
OPERATION AND MAINTENANCE
Damage Requiring Service: The appliance should be serviced by
qualified service personnel when:
Magnadyne Corporation or its authorized agents will within 1 year from the
date of sale to you, repair, replace or refund the retail sales price of said prod-
uct or any part thereof, at the option of the Magnadyne Corporation or its
authorized agents, if said product or part is found defective in materials or
workmanship, when properly connected and operating on the correct power
requirements designated for the specific product. This warranty and
Magnadyne Corporation or its authorized agents obligations hereunder do not
apply where the product was; damaged while in the possession of the con-
sumer, subjected to unreasonable or unintended use, not reasonably main-
tained, utilized in commercial or industrial operations, or serviced by anyone
other than Magnadyne Corporation or its authorized agents, or where the
warning seal on the product is broken or the power and/or plugs are detached
from the unit. Magnadyne Corporation or any of its authorized agents will not
assume any labor costs for the removal and re-installation of any product
found to be defective, or the cost of transportation to Magnadyne Corporation
or its authorized agents. Such costs are the sole responsibility of the purchas-
er.
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance;or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
Servicing: The user should not attempt to service the appliance
beyond that described in the operating instructions. All other serv-
icing should be referred to qualified service personnel.
Caution:
Compact disc should be stored in a container or vinyl bag to pre-
vent contamination. Disc should not be placed in locations
exposed to sunlight or heat.
This warranty does not cover the cabinet appearance items or accessories
used in connection with this product, or any damaged to recording or record-
ing tape, or any damage to the to the products resulting from improper instal-
lation, alteration, accident, misuse, abuse or acts of nature.
Warnings
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT
BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAM-
AGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO
EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT
THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND 1 YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable.
Handle CD’s
Properly
Do Not Touch
Do Not Get Dirt
Do Not Write on
CD’s
on CD’s
CD’s
Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or con-
sequential damages, so the above limitations or exclusion may not apply to
you. This warranty gives you specific legal rights, and you may have other
rights that vary from state to state.
104
40
F
C
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA
90220, or 2061 Cohen Street, Montreal, Quebec H4R 2N7. Return Authorization
must be obtained before sending, or merchandise may be refused.
Do Not Scratch
Keep Below 1040
Fahrenheit
Do Not Bend CD’s
CD’s
LS7600CDSGINS Rev. A 4-26-00
12
|